We have compiled a list of manufacturers, distributors, product information, reference prices, and rankings for Air knife.
ipros is IPROS GMS ・ IPROS One of the largest technical database sites in Japan that collects information on.

Air knife×ティックコーポレーション - List of Manufacturers, Suppliers, Companies and Products

Air knife Product List

1～6 item / All 6 items

Displayed results
[Sonic] Water Drainage Drying Case Studies: Removal of Residual Water After Pallet Cleaning

[Sonic] Water Drainage Drying Case Studies: Removal of Residual Water After Pallet Cleaning

I have made it possible to repeatedly position the air knife.

We proposed 12 Sonic 70 blowers with 7.5 horsepower motors, enclosures, Sonic HEPA filters, and two custom Sonic XE air knives measuring 13 inches. The performance of the air knives delivered at the beginning of this system perfectly matched the blow level requested by the customer. The results of the contamination test also confirmed that Sonic's HEPA filters maintained the requested 0.3μ. Additionally, to operate most effectively while keeping the noise level below 80dB, the angle and distance of the air knives are very important, so we manufactured custom Sonic air knives to fit the existing air knife enclosures, allowing for repeated positioning of the air knives. [Content] [Issues] - Compressed air with HEPA filters - The factory was using more compressed air for automatic devices on the production line and other equipment on a daily basis. - They were compelled to add another air compressor to avoid pressure drops due to increased demand for compressed air. For more details, please contact us or download the catalog.

  • Drying Equipment
  • Pneumatic Equipment
  • nozzle

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Sonic Water Drainage Drying Case Collection - Propane Gas Cylinder

Sonic Water Drainage Drying Case Collection - Propane Gas Cylinder

Tilt the two air knives slightly and present a blowing method that focuses on the body and upper part.

The gap or slot of the air knife can be adjusted in length to allow for a wider gap. This means that the air knife, which is concentrated on the body, can maintain a standard gap while separately adjusting the knife gap at the top and bottom to hit the handle and the lower ring. This method not only allows the wind to effectively hit the body of the canister but also reduces the required power consumption. SONIC has also suggested further cost reduction by switching from plated steel pipes to ABS piping to lower prices even more. [Contents] [Issues] ○ Yankee Gas faced the problem of propane gas canisters not being sufficiently dry before going to the painting process while changing their solvent-based painting system. ○ Proper drying of the canisters is essential for effective painting. ○ The drying method they were using involved compressed air, which was ineffective and did not adequately remove moisture for painting. ○ High humidity means that no matter how much compressed air is applied, moisture remains on the canisters. For more details, please contact us or download the catalog.

  • Drying Equipment
  • Pneumatic Equipment
  • nozzle

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Must-read before selection! 'Trivia about Air Knives'

Must-read before selection! 'Trivia about Air Knives'

Are you having trouble with the essential "water droplet removal and drying process" after cleaning? We will provide you with a booklet that includes case studies on solving post-cleaning issues across various industries!

Are you having trouble with the blow process using air? There is always a cleaning process for parts (such as components) and products (like PET bottles and retort pouches). Following that process, there is always a drying process. I have heard that this drying is an eternal theme. Shall we finally resolve this eternal theme? Sonic's blowers and air knives efficiently and economically solve problems with high air volume and high-speed air! ▼ A job that required a pressure of 0.4 MPa can be achieved with just 29 kPa! ▼ When comparing the airflow of a compressor and a Sonic blower, to achieve an airflow of 7 m³/min, a compressor requires 62.5 horsepower. In contrast, the Sonic blower can achieve this with only 4 horsepower. The difference is significant compared to compressors and domestic blowers! In "Air Knife Trivia," we have numerous case studies for problem-solving. 【Case Studies】 ■ Automotive industry case studies ■ Food and beverage industry case studies ■ Pharmaceutical industry case studies ■ Steel industry case studies, etc. *For more details, please request materials or view the PDF data from the download.

  • Other drying equipment
  • nozzle
  • Pneumatic Equipment

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
[Sonic] Water Drainage Drying Case Studies: Issues with Bottle Labeling

[Sonic] Water Drainage Drying Case Studies: Issues with Bottle Labeling

There was no need for additional construction, and it fit into the existing production line.

Sonic Corporation decided to operate the Sonic150 with 25 horsepower and two air knives, and to circulate air to raise the temperature coming from the air knives. The concept behind Sonic Corporation's revolutionary VT (patent pending) design is to utilize the pressure heat from the blower by partially circulating air. The exit temperature from the air knives will be approximately 45°C to 50°C. This method does not require an external thermal system. The air knives are installed about 10mm away from the bottles, allowing the bottles to pass through at a wind speed of approximately 9,300m/min. The high-speed air and heated exit temperature melt the ice and turn the remaining moisture into a mist. As a result, the bottles can be completely dried. [Content] [Issues] ○ Moisture and cold air leave water droplets on the glass, resulting in the reformation of water droplets before labeling. ○ Labels cannot be applied until the bottles are dried. ○ The injection and labeling of bottles require empty bottles to be stacked in a heated warehouse, and this process can only occur after they have been warmed. For more details, please contact us or download the catalog.

  • Drying Equipment
  • Pneumatic Equipment
  • nozzle

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
[Third Edition] Things You Want to Read Before Selection! "Trivia About Air Knives"

[Third Edition] Things You Want to Read Before Selection! "Trivia About Air Knives"

Third installment! For those who have been unable to solve problems until now... Here are numerous case studies for problem-solving!

Are there any issues with the food processing drying process or the blowing off of water droplets from cans/bottles? The Sonic Air Knife System, with its high volume and high-speed air, efficiently and economically solves such problems! Tasks that required a pressure of 0.4 MPa can now be achieved with just 15-20 kPa! When comparing the airflow of a compressor and a Sonic blower, obtaining an airflow of 7 m³/min requires 60 HP (53 kW) with a compressor. In contrast, the Sonic blower achieves this with only 5 HP (3.7 kW). The difference is significant compared to compressors and domestic blowers! For those who have been unable to resolve issues until now… we have numerous case studies for you! 【Case Studies】 - Examples for the food/beverage industry - Examples for the automotive industry - Examples for the pharmaceutical industry - Examples for the steel industry, etc. *For more details, please refer to the PDF materials or feel free to contact us. *We also have a collection of case studies that we send out regularly. If you have any requests, please feel free to reach out to our staff.

  • nozzle
  • Hot air dryer
  • Pneumatic Equipment

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Continued! Things to read before selection! "Trivia about Air Knives"

Continued! Things to read before selection! "Trivia about Air Knives"

Are you having trouble with the essential "water droplet removal and drying process" after cleaning? We will provide you with a booklet that includes case studies on solving post-cleaning issues across various industries!

In response to popular demand, we are publishing "Continuation! Things You Want to Read Before Selection: 'Air Knife Trivia'!" It can dry with up to 1/4 the electricity compared to blowing with a compressor! There is always a cleaning process for parts (such as components) and products (like PET bottles and retort pouches). After that process, there is always a drying process. I have heard that this drying is an eternal theme. Shall we finally conclude this eternal theme? Sonic's blowers and air knives efficiently and economically solve problems with large air volume and high-speed air! ▼ A job that required 0.4 MPa of pressure is achieved with just 29 kPa! ▼ When comparing the air volume of a compressor and a Sonic blower, to achieve an air volume of 7 m³/min, a compressor requires 62.5 horsepower. In contrast, a Sonic blower can achieve this with only 4 horsepower. The difference is significant compared to compressors and domestic blowers! "Air Knife Trivia" includes numerous case studies for problem-solving. 【Examples of case studies】 ■ Automotive industry case studies ■ Food/Beverage industry case studies ■ Pharmaceutical industry case studies ■ Steel industry case studies, etc.

  • nozzle
  • Other drying equipment
  • Pneumatic Equipment

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
COPYRIGHT © 2001-2025 IPROS CORPORATION ALL RIGHTS RESERVED.